This article mainly introduces:

Canada hydraulic cylinder,extra high pressure cylinder manufacturer,extra high pressure cylinder

(Canada extra high pressure cylinder,produced by Hengyu Hydraulic Co., Ltd）

extra high pressure cylinder are widely used in Canada，because of excellent fatigue and impact resistance，no need for deceleration device，high work efficiency.So our company has designed extra high pressure cylinder for customers from Canada.

Introduction to extra high pressure cylinder:

The scar on the sliding surface of the extra high pressure cylinder piston will transfer with use. Before the piston is installed, there are scars on its sliding surface, which are installed intact and untreated, and these scars will in turn scratch the inner surface of the extra high pressure cylinder wall. Therefore, before installation, these scars must be fully repaired.

If the extra high pressure cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the extra high pressure cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow extra high pressure cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the extra high pressure cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the extra high pressure cylinder includes the leakage caused by excessive wear of the extra high pressure cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and extra high pressure cylinder, and the phenomenon of "pulling the extra high pressure cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

If the seal of the extra high pressure cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and extra high pressure cylinder, and the phenomenon of "pulling the extra high pressure cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The repair method of extra high pressure cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about extra high pressure cylinder:

Are hydraulic cylinders divided into oil cylinders and water cylinders? What's the difference between the two types?
There are oil cylinders and water cylinders. The two cylinders are used in different environments. Oil cylinders are generally used in places where there is less demand for media, which is our most common hydraulic cylinders. Water cylinders are mainly used for large tonnage presses. Because the equipment is too large, the use of hydraulic oil will cause a relatively large waste. However, water is not pure water, there are oil-in-water emulsion and water-in-oil emulsion. Water has another benefit: it's flame retardant. It is especially suitable for some flammable and explosive occasions. Or with water glycol. The use of pure water is very little, mainly because the seal is not good and easy to rust.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.