This article mainly introduces:

Tanzania hydraulic cylinder,trailer hydraulic cylinder manufacturer,trailer hydraulic cylinder

(Tanzania trailer hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

trailer hydraulic cylinder are widely used in Tanzania，because of long service life，smooth movement，high work efficiency.So our company has designed trailer hydraulic cylinder for customers from Tanzania.

Introduction to trailer hydraulic cylinder:

Repair method of small range wear of oil trailer hydraulic cylinder: 1. Use oxygen-acetylene flame to bake the scratched part (master the temperature, avoid surface annealing), bake the oil on the metal surface all the year round until no sparks splash; 2. The scratched part is treated with an Angle grinder, the grinding depth is more than 1 mm, and the groove is polished along the guide rail, preferably a dovetail groove. Scratch both ends of the drilling deeper, change the force situation; 3. Clean the surface with absorbent cotton dipped in acetone or anhydrous ethanol.

When the initial action of the trailer hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the trailer hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

The pressure of the sliding surface of the trailer hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the trailer hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

trailer hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the trailer hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

Answers to some questions about trailer hydraulic cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

Need a hydraulic cylinder, vertical upward 10 seconds to lift 20 tons of weight up 2 meters, how large cylinder and rod, how much pressure to use the plunger pump and how big?
The first thing to determine the system pressure, let's say 25 mpa, can take into account cost and performance. 1 Cylinder area 20000/250=80 square cm cylinder diameter (80/3.14) squared x2=200 mm 2 cylinder volume 80x200=16000 ml =16 L 3 Required pump flow 16x60/10=96 L/min 4 Power 96x25/55=43 kW 45 kW motor is available.