This article mainly introduces:

Malaysia hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Malaysia yg series hydraulic cylinder,produced by Hebei Hengyu company）

yg series hydraulic cylinder are widely used in Malaysia，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed yg series hydraulic cylinder for customers from Malaysia.

Introduction to yg series hydraulic cylinder:

The main role of the yg series hydraulic cylinder: the yg series hydraulic cylinder is an executive element in the hydraulic transmission system, which is an energy conversion device that converts hydraulic energy into mechanical energy. The hydraulic motor realizes continuous rotary motion, while the yg series hydraulic cylinder realizes reciprocating motion. The structure of the yg series hydraulic cylinder has three categories: piston yg series hydraulic cylinder, plunger yg series hydraulic cylinder, swing yg series hydraulic cylinder, piston yg series hydraulic cylinder and plunger yg series hydraulic cylinder to achieve reciprocating linear motion, output speed and thrust, swing yg series hydraulic cylinder to achieve reciprocating swing, output angular speed (speed) and torque. In addition to the single use of the yg series hydraulic cylinder, two or more can be combined or used in combination with other mechanisms. To fulfill a special function. The yg series hydraulic cylinder has simple structure and reliable operation, and has been widely used in the hydraulic system of machine tools.

How to determine the working pressure of the yg series hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, yg series hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

yg series hydraulic cylinder piston rod material introduction: In general, we use 45 steel to produce yg series hydraulic cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

When the hydraulic oil is not pumped into the yg series hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the yg series hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

Answers to some questions about yg series hydraulic cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.