This article mainly introduces:

Oman hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(Oman tension cylinder,produced by Hengyu Group）

tension cylinder are widely used in Oman，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed tension cylinder for customers from Oman.

Introduction to tension cylinder:

Most of the failure of the tension cylinder is because there is a foreign body in the tension cylinder into the failure of the tension cylinder, the most problematic is that it is difficult to determine when the foreign body is into the tension cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

The tension cylinder is mainly composed of body, piston, piston rod, tension cylinder head, tension cylinder bottom, piston rod head and related auxiliary devices. The piston divides the tension cylinder into two chambers, and moves reciprocally in the tension cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the tension cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the tension cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the tension cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the tension cylinder bottom and the tension cylinder head is serious, so the buffer deceleration should be set at both ends of the tension cylinder The working medium of the tension cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; tension cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the tension cylinder: The buffer structure of the tension cylinder is to prevent the piston from colliding with the tension cylinder head at the end of the stroke.

tension cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the tension cylinder is placed for a period of time, the tension cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

When the tension cylinder is installed, the piston and the tension cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the tension cylinder head boss is easy to cause scars when it hits the inner surface of the tension cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized tension cylinders, only careful and careful operation can be avoided.

Answers to some questions about tension cylinder:

What is the meaning of cylinder ejection on the injection mold, and what is the difference between cylinder ejection and ordinary ejection?
Usually requires the front die ejection will use the cylinder to drive the thimble plate to achieve the ejection of the thimble. There is also a case that the mold is very large or long, and the balance of the ejector rod of the injection molding machine is not enough, and the cylinder ejector will also be used.

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.