This article mainly introduces:

Libya hydraulic cylinder,100 ton hydraulic cylinder manufacturer,100 ton hydraulic cylinder

(Libya 100 ton hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

100 ton hydraulic cylinder are widely used in Libya，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed 100 ton hydraulic cylinder for customers from Libya.

Introduction to 100 ton hydraulic cylinder:

In the case of serious wear on the inner surface of the 100 ton hydraulic cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the 100 ton hydraulic cylinder manufacturing process for replacement. The 100 ton hydraulic cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Do not enter foreign bodies when installing the 100 ton hydraulic cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

100 ton hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

If it is found that the 100 ton hydraulic cylinder lubrication is poor or the 100 ton hydraulic cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the 100 ton hydraulic cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the 100 ton hydraulic cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the 100 ton hydraulic cylinder center line. In this way, when the piston works in the 100 ton hydraulic cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the 100 ton hydraulic cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

Answers to some questions about 100 ton hydraulic cylinder:

What is the difference between gas-hydraulic pressurized cylinder, pneumatic cylinder and oil cylinder?
The cylinder block is small and the force is large, constant speed and variable speed can be used (easy to change), the adjustment of the output is also convenient, and the freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Easy cylinder control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion.

Why does the tipping bucket cylinder have a cylinder withdrawal problem?
This problem may have a certain relationship with the operation of the driver, the main reasons are the following two situation analysis: 1, the current domestic loader working device is mostly a six-link mechanism, the six-link mechanism in the bucket to the limit position, lift the boom, the rotating bucket cylinder will appear "cylinder pulling" phenomenon, that is, the piston rod of the rotating bucket cylinder will be pulled out. In this case, in order to protect the cylinder, a pressure overload protection valve with large and small cavities is provided on the multi-way valve rotating bucket link (large chamber 18MPa, small chamber 12MPa). 2, before the cylinder is assembled to the whole machine, the cylinder is not limited, the piston rod of the cylinder can be pulled in place before and after, but when it is installed on the whole machine, in order to avoid the cylinder pulling out, the limit switch is installed according to the regulations.