This article mainly introduces:

Tanzania hydraulic cylinder,pressure plate hydraulic cylinder manufacturer,pressure plate hydraulic cylinder

(Tanzania pressure plate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

pressure plate hydraulic cylinder are widely used in Tanzania，because of no need for deceleration device，long service life，smooth movement.So our company has designed pressure plate hydraulic cylinder for customers from Tanzania.

Introduction to pressure plate hydraulic cylinder:

pressure plate hydraulic cylinder use should try to avoid sealing belt into the pressure plate hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the pressure plate hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the pressure plate hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

pressure plate hydraulic cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When installing the pressure plate hydraulic cylinder, the axial ends of the pressure plate hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the pressure plate hydraulic cylinder, there is axial expansion. If the two ends of the pressure plate hydraulic cylinder are fixed, all parts of the pressure plate hydraulic cylinder will be deformed. When disassembling the pressure plate hydraulic cylinder, it is strictly forbidden to hammer the pressure plate hydraulic cylinder and the piston surface, such as the pressure plate hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

The pressure plate hydraulic cylinder should be vented: when the pressure plate hydraulic cylinder is installed or parked for a long time to work again, the air will penetrate into the pressure plate hydraulic cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the pressure plate hydraulic cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the pressure plate hydraulic cylinder, the oil is best entered and discharged from the highest point of the pressure plate hydraulic cylinder. pressure plate hydraulic cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

Answers to some questions about pressure plate hydraulic cylinder:

How does the clamping cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, The executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, The control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, The auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.