This article mainly introduces:

UAE hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

(UAE tailplate hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

tailplate hydraulic cylinder are widely used in UAE，because of no need for deceleration device，long service life，smooth movement.So our company has designed tailplate hydraulic cylinder for customers from UAE.

Introduction to tailplate hydraulic cylinder:

Causes and countermeasures of oil tailplate hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the tailplate hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the tailplate hydraulic cylinder is visibly scarred, the tailplate hydraulic cylinder must be replaced. It can be pressurized at one end of the tailplate hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most tailplate hydraulic cylinder piston drift may not come from the tailplate hydraulic cylinder, the above method to determine the tailplate hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

tailplate hydraulic cylinder use should try to avoid sealing belt into the tailplate hydraulic cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the tailplate hydraulic cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the tailplate hydraulic cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

When the tailplate hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the tailplate hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

When the tailplate hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The tailplate hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the tailplate hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil tailplate hydraulic cylinder should not be in direct contact with water vapor for a long time. The tailplate hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the tailplate hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the tailplate hydraulic cylinder Before working, the tailplate hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the tailplate hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about tailplate hydraulic cylinder:

What steel pipe does hydraulic cylinder use? This problem is very general. Carbon steel pipe or ordinary seamless steel pipe are all ok, but then there are rolling, quilting, heat treatment and other steps, and the requirements are different, the wall thickness is different, the material is different. It depends on the circumstances.

CNC lathe rotary cylinder oil leakage and treatment methods
Oil leakage often occurs when the cylinder (especially the hollow cylinder) of the CNC lathe is installed. First check the cylinder yaw, be sure to reach or close to the required value, generally the cylinder requires the outer beat within 1 wire. Otherwise, too much beating is sure to leak oil. Then check whether the tubing is smoothly downward at a certain Angle, and can not bend. Look at the pipe outlet can not go into the oil level, to a little higher. Otherwise, there's back pressure and it's gonna leak.