This article mainly introduces:

Estonia hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

(Estonia steering power cylinder,produced by Hebei Hengyu company）

steering power cylinder are widely used in Estonia，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed steering power cylinder for customers from Estonia.

Introduction to steering power cylinder:

If the steering power cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the steering power cylinder. The internal parts of the steering power cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the steering power cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the steering power cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the steering power cylinder bore processing is out of whack. Because the piston and steering power cylinder, guide rail and piston rod are relative If the steering power cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling steering power cylinder weight composition and calculation. The weight of the steering power cylinder is composed of the steering power cylinder diameter, the outer diameter and weight of the steering power cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Do not enter foreign bodies when installing the steering power cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

steering power cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the steering power cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the steering power cylinder. c. The steering power cylinder seal is extruded, if the O-ring is obviously extruded at the steering power cylinder seal, replace the steering power cylinder seal.

In use, the steering power cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the steering power cylinder.

Answers to some questions about steering power cylinder:

What is hydraulic cylinder？ How to use hydraulic cylinder？ what is the application of hydraulic cylinder?
Hydraulic cylinder is the hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating movement (or swing movement). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the hydraulic cylinder is proportional to the effective area of the piston and the pressure difference between the two sides. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston, piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential. Hydraulic cylinders are mainly used in machinery.

How to choose cylinder size, pump type, motor power for a 30-ton press?
30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.