This article mainly introduces:

Republic of Lithuania hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

(Republic of Lithuania steering power cylinder,produced by Hengyu Hydraulic Co., Ltd）

steering power cylinder are widely used in Republic of Lithuania，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed steering power cylinder for customers from Republic of Lithuania.

Introduction to steering power cylinder:

What kind of process is used in the steering power cylinder to make high-quality steering power cylinder products: the body is the main component of the steering power cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The steering power cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the steering power cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the steering power cylinder increases by 25%. If the service life of the steering power cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. steering power cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the steering power cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and steering power cylinder are stuck or the steering power cylinder is blocked. At this time, no matter how to manipulate, the steering power cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steering power cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Disassembly steering power cylinder: When disassembly steering power cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the steering power cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the steering power cylinder.

When producing oil steering power cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

steering power cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the steering power cylinder head itself is the guide sleeve of the piston rod, the steering power cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the steering power cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Answers to some questions about steering power cylinder:

What material should be selected to seal the cylinder?
The choice of material for sealing is related to the working environment, strength, and medium of your equipment.

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.