This article mainly introduces:

Costa Rica hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

(Costa Rica series synchronous cylinder,produced by Hengyu Hydraulic Cylinder Factory）

series synchronous cylinder are widely used in Costa Rica，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed series synchronous cylinder for customers from Costa Rica.

Introduction to series synchronous cylinder:

The assembly work of the series synchronous cylinder has a great impact on the quality of the series synchronous cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the series synchronous cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

Causes and countermeasures of oil series synchronous cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the series synchronous cylinder will lead to premature wear of the piston seal, replace the piston seal; If the series synchronous cylinder is visibly scarred, the series synchronous cylinder must be replaced. It can be pressurized at one end of the series synchronous cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most series synchronous cylinder piston drift may not come from the series synchronous cylinder, the above method to determine the series synchronous cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

series synchronous cylinder installation precautions: Before installing the series synchronous cylinder into the system, the parameters on the series synchronous cylinder label should be compared with the parameters when ordering. The base of the series synchronous cylinder must have sufficient stiffness, otherwise the series synchronous cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Answers to some questions about series synchronous cylinder:

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.