Release time：2023-11-12 15:31:43 Hits： Current position: Home > News
This article mainly introduces:
Bahrain hydraulic cylinder,retractable cylinder manufacturer,retractable cylinder
(Bahrain retractable cylinder,produced by Hebei Hengyu company）
retractable cylinder are widely used in Bahrain，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed retractable cylinder for customers from Bahrain.
When the retractable cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the retractable cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the retractable cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the retractable cylinder can meet the requirements by grinding. However, the life and reliability of this repair retractable cylinder are not high.
Classification of retractable cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.
What kind of process is used in the retractable cylinder to make high-quality retractable cylinder products: the body is the main component of the retractable cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The retractable cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the retractable cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the retractable cylinder increases by 25%. If the service life of the retractable cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. retractable cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the retractable cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and retractable cylinder are stuck or the retractable cylinder is blocked. At this time, no matter how to manipulate, the retractable cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the retractable cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.
The method of sleeve retractable cylinder to improve the processing quality: there is a big gap in the service life of post-plating polishing and post-plating polishing, especially in mass production. Strictly clean the flying edge and burr of mechanical components, especially the edge of the sealing groove, and the tiny metal burr, strictly clean before assembly. The surface fatigue strength and stress corrosion resistance of the retractable cylinder can be significantly improved by rolling in the finishing of the inner holes of the retractable cylinder. The roughness of the surface of the friction pair is generally controlled between Ra0.4 and 0.8.
The hydraulic cylinder is slow when moving forward and faster when moving back.
If the cylinder is single, it is slow when it is moving forward without the rod cavity, and fast when it is shrinking.
When does the cylinder rotate?
The piston rod inside the multistage plunger cylinder can be rotated, and it will rotate when it is subjected to tangential force.
Add Wechat