This article mainly introduces:

Estonia hydraulic cylinder,lifting platform cylinder manufacturer,lifting platform cylinder

(Estonia lifting platform cylinder,produced by Hebei Hengyu company）

lifting platform cylinder are widely used in Estonia，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed lifting platform cylinder for customers from Estonia.

Introduction to lifting platform cylinder:

How to determine the working pressure of the lifting platform cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, lifting platform cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

What kind of process is used in the lifting platform cylinder to make high-quality lifting platform cylinder products: the body is the main component of the lifting platform cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The lifting platform cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the lifting platform cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the lifting platform cylinder increases by 25%. If the service life of the lifting platform cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. lifting platform cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the lifting platform cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and lifting platform cylinder are stuck or the lifting platform cylinder is blocked. At this time, no matter how to manipulate, the lifting platform cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the lifting platform cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The advantages and disadvantages of the lifting platform cylinder: the surface of the lifting platform cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the lifting platform cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

When purchasing the lifting platform cylinder, try to clarify the following parameters of the lifting platform cylinder: A. lifting platform cylinder diameter, rod diameter, stroke; B. Working pressure or lifting platform cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right lifting platform cylinder type can be found accurately and quickly.

Answers to some questions about lifting platform cylinder:

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

How to calculate cylinder pressure?
Hydraulic pressure area of cylinder × hydraulic pressure = output force of cylinder 200mm=20cm 100mm=10cm 15Mpa=150Kg/cm2 Cylinder thrust: 3.14×10×10 area ×150 pressure =47100Kg=47.1t cylinder pulling force: 3.14×(10×10-5×5) Area ×150 pressure =35325Kg=35.325t The above calculation did not consider the resistance of oil return, because you did not provide oil return pressure. But the impact should be small.