This article mainly introduces:
Peru hydraulic cylinder,servo cylinder manufacturer,servo cylinder
(Peru servo cylinder,produced by Hengyu Group）
servo cylinder are widely used in Peru，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed servo cylinder for customers from Peru.
The servo cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.
servo cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the servo cylinder is placed for a period of time, the servo cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.
When the servo cylinder is customized, if there are high requirements for the quality of the servo cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the servo cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the servo cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.
When the initial action of the servo cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the servo cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.
What are the requirements for hydraulic cylinder assembly? ① The installation of the cylinder should be solid and reliable. In order to prevent the influence of thermal expansion, in the case of large stroke and hot working conditions, one end of the cylinder must be kept floating.② pipe connection shall not be relaxed.③ The mounting surface of the hydraulic cylinder and the sliding surface of the piston rod should maintain sufficient parallelism and perpendicality.④ The central axis of the moving cylinder should be concentric with the center line of the load force, otherwise it will cause lateral force, which is easy to wear the seal And piston damage. The greater the distance between the supporting points of the piston rod, the smaller its wear. For the hydraulic cylinder of the moving object, the installation should keep the cylinder parallel with the moving object, and the degree of non-parallelism is generally not greater than 0.05mm/m. ⑤The sealing ring should not be installed too tightly, especially the U-shaped sealing ring.
What is the clearance between the cylinder and the piston?
The gap between the cylinder and the piston in the radius is generally 40 wires, that is, about 0.4mm, and the gap of the cylinder with different diameters will be slightly different. Generally, the inner diameter of the cylinder is larger than the outer diameter of the piston, so as to prevent the friction between the outer surface and the inner surface of the cylinder during the operation of the piston. In order to ensure that the cylinder has a rod cavity and a rodless cavity seal, a sealing device, that is, a sealing ring, is installed on the outer surface of the piston. The sealing ring form is not exactly the same, the O-type sealing ring is generally used under low pressure, and the lip sealing ring is used under high pressure. At the same time, the outer circle of the piston is also equipped with a dust ring and a wear ring. As long as the cylinder seal fails, all the internal seals should be replaced.
Add Wechat