This article mainly introduces:

Malaysia hydraulic cylinder,single rack cylinder manufacturer,single rack cylinder

(Malaysia single rack cylinder,produced by Hebei Hengyu company）

single rack cylinder are widely used in Malaysia，because of excellent temperature resistance，long service life，clever hydraulic energy conversion.So our company has designed single rack cylinder for customers from Malaysia.

Introduction to single rack cylinder:

The single rack cylinder should not be mixed with foreign objects during assembly, which will cause scars. Before the total assembly of the single rack cylinder, all parts must be fully removed and cleaned. When the parts are installed with burrs or dirt, foreign objects are easily embedded into the surface of the single rack cylinder wall due to the stiffness and the weight of the parts, causing scars.

single rack cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a single rack cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' single rack cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the single rack cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The single rack cylinder mainly outputs linear motion and force. The single rack cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston single rack cylinder, plunger single rack cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger single rack cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

When the single rack cylinder is in use, ensure that the single rack cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

If air enters the hydraulic system, the single rack cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

Answers to some questions about single rack cylinder:

What factors does the movement speed of the cylinder in the hydraulic system depend on?
The hydraulic system should be the piston movement in the cylinder, and the speed should also be the speed of the piston, according to the piston speed formula: v=4qm/pai*(D^2-d^2) where q is the flow rate of the input hydraulic cylinder, m is the volumetric efficiency of the hydraulic cylinder, D, d is the diameter of the piston and piston rod, because other factors are determined, the movement speed of the cylinder depends on the flow rate.

Can one hydraulic pump with two cylinders work?
A hydraulic pump with two cylinders will work. Commonly used hydraulic pump types: 1, according to whether the flow can be adjusted can be divided into: variable pump and quantitative pump. The output flow can be adjusted according to the needs of the variable pump, the flow can not be adjusted called quantitative pump. 2, according to the pump structure commonly used in the hydraulic system is divided into: gear pump, vane pump and plunger pump 3 kinds. Gear pump: small volume, simple structure, the cleanliness of the oil requirements are not strict, the price is cheaper; However, the pump shaft is subjected to unbalanced force, serious wear and leakage. Vane pump: divided into double acting vane pump and single acting vane pump. The pump has uniform flow, smooth operation, low noise, higher pressure and volumetric efficiency than gear pump, and more complex structure than gear pump.